304不銹鋼衛生級內螺紋電動三通球閥廠家

內螺紋電動三通球閥產品特點
1．三通球閥有兩座和四座密封結構，閥芯孔道有L型和T型兩種結構形式，采用控制閥芯旋轉角度，改變閥芯孔道與管道口的連接狀態，可實現對三條支管不同的組合控制。三通球閥流通能力大，可控制氣體，蒸汽，液體，更適用于控制高粘度，纖維顆粒狀的流體。也適用于密封要求較嚴格的場合。
2．兩閥座密封三通球閥具有結構緊湊、外形美觀、密封性能好，它能實現對管道中介質流向的切換。也能使相互垂直的兩個通道連通或關閉。
3．四閥座密封三通球閥具有造型美觀、結構緊湊合理，它不僅可實現介質流向的切換，也可使三個通道相互連通，同時可關閉任意一個通道，使另外兩個通道連通，靈活控制管路是介質的合流或分流。
4．T型閥芯孔道可使三條正交的管道互相連通或切換，起分流或合流作用；L型孔道連接相互正交的兩管道。使另一條孔道切斷，起改變介質流向作用。
5．三通球閥的主要產品系列：如流向圖所示選擇工況。

Product features of internal thread electric three-way ball valve

1. The three-way ball valve has two-seat and four-seat sealing structures. The spool has two structural forms, L-type and T-type. The rotation angle of the spool is controlled, and the connection state of the spool and the pipe port can be changed. The three branch pipes can be different Combination control. The three-way ball valve has a large flow capacity and can control gas, steam, and liquid. It is more suitable for controlling high-viscosity, fibrous and granular fluids. It is also suitable for occasions with strict sealing requirements.

2. The two-seat sealed three-way ball valve has a compact structure, beautiful appearance, and good sealing performance. It can switch the flow direction of the medium in the pipeline. It can also connect or close the two channels perpendicular to each other.

3. The four-seat sealed three-way ball valve has beautiful appearance, compact and reasonable structure. It can not only switch the flow direction of the medium, but also make the three channels communicate with each other. At the same time, it can close any one of the channels to connect the other two channels and control the tube flexibly. Path is the confluence or divergence of media.

4. T-shaped spool orifice allows three orthogonal pipelines to communicate or switch to each other to split or merge; L-shaped orifice connects two orthogonal pipelines. Cut off the other channel to change the flow direction of the medium.

5. The main product series of the three-way ball valve: select the working condition as shown in the flow diagram.

電動內螺紋三通球閥安裝注意事項

(1)取掉法蘭端兩邊的保護蓋，在閥*打開的狀態下進行沖洗清潔。
(2)安裝前應按規定的信號(電動或氣動)進行整機測試(防止因運輸產生振動影響使用性能)，合格后方可上線安裝(接線按電動執行機構線路圖)。
(3)準備與管道連接前，須沖洗和清除干凈管道中殘存的雜質(這些物質可能會損壞閥座和球)。
(4)在安裝期間，請不要用閥的執行機構部分作為起重的吊裝點，以避免損壞執行機構及附件。
(5)本類閥應安裝在管道的水平方向或垂直方向。
(6)安裝點附近的管道不可有低垂或者承受外力的現象，可以用管道支架或者支撐物來消除管線的偏離。
(7)與管道連接后，請用規定的扭矩交叉鎖緊法蘭連接螺栓。

Installation precautions for electric internal thread three-way ball valve

(1) Remove the protective covers on both sides of the flange, and rinse and clean with the valve fully opened.

(2) Before installation, the whole machine should be tested according to the specified signal (electric or pneumatic) (to prevent the vibration caused by transportation from affecting the performance), and then it can be installed online (wiring according to the wiring diagram of the electric actuator).

(3) Before preparing to connect with the pipeline, flush and remove the remaining impurities in the pipeline (these substances may damage the valve seat and ball).

(4) During installation, please do not use the actuator part of the valve as a lifting point to avoid damage to the actuator and accessories.

(5) This type of valve should be installed in the horizontal or vertical direction of the pipeline.

(6) The pipeline near the installation point must not sag or bear external forces. Pipe supports or supports can be used to eliminate the deviation of the pipeline.

(7) After connecting with the pipeline, please cross-tighten the flange connecting bolts with the specified torque.

電動內螺紋三通球閥的密封材料
球閥的密封性能在很大程度上取決于密封件的材料，正確合理的選擇密封材料對保證球閥工作性能，延長使用壽命具有重要意義。對材料的要求有具有高的耐磨損耐溶解性能力，應該具有足夠高的強度，能長期經受流體壓力作用，并能多次拆裝，彈性和塑性好，滑動摩擦系數和膨脹系數低，耐磨性能和自潤滑性能優良，并具有好的不滲透性和不吸濕性等，能夠耐寒耐熱和耐溫度的急劇變化，并有良好的導熱性能。密封材料有非金屬和金屬密封材料兩種。
1．非金屬密封材料：常用的有纖維材料，橡膠，工程塑料以及碳素材料等。這些材料具有低的彈性模數和高的泊桑系數，因此，在較低的密封力作用下，即能獲得大的彈塑性變形，對可能產生滲透的間隙有較好的填塞作用。
2．金屬密封材料：常用的有鋁，銅及硬質合金，鋁銅常用于制造球閥用法蘭墊片，硬質合金則用于高溫球閥閥座和球體的密封面。

Sealing material of electric internal thread three-way ball valve

The sealing performance of the ball valve depends to a large extent on the material of the seal. The correct and reasonable selection of the sealing material is of great significance to ensure the working performance of the ball valve and prolong the service life. The material is required to have high abrasion resistance and solubility resistance, should have high enough strength, can withstand the action of fluid pressure for a long time, and can be disassembled many times, with good elasticity and plasticity, and low sliding friction coefficient and expansion coefficient. Excellent wear resistance and self-lubricating properties, good impermeability and non-hygroscopicity, etc., can withstand cold, heat, and rapid changes in temperature, and have good thermal conductivity. There are two types of sealing materials: non-metallic and metallic sealing materials.

1. Non-metallic sealing materials: fiber materials, rubber, engineering plastics and carbon materials are commonly used. These materials have low elastic modulus and high Poisson coefficient. Therefore, under the action of low sealing force, large elastoplastic deformation can be obtained, and the gap that may be penetrated has a better filling effect.

2. Metal sealing materials: commonly used are aluminum, copper and cemented carbide. Aluminum and copper are often used to make flange gaskets for ball valves, and cemented carbide is used for high-temperature ball valve seats and the sealing surfaces of spheres.

內螺紋電動三通球閥主要零件材料及適用溫度、介質

內螺紋電動三通球閥應用規范

內螺紋電動三通球閥性能規范

圖片信息：304不銹鋼衛生級內螺紋電動三通球閥廠家

公司簡介：

安徽利勒潔凈設備科技有限公司是國內專業生產制造潔凈衛生級閥門管件，主要應用于食品機械行業、制藥機械行業、乳制品行業、釀酒飲料行業以及精細化工等行業高精度衛生級流體設備的專業生產廠家，產品規格齊全；產品主要有：

無菌隔膜閥，卡箍直通隔膜閥，三通隔膜閥，法蘭隔膜閥，氣動隔膜閥，U型隔膜閥，罐底隔膜閥 ；

無菌球閥，卡箍直通球閥，螺紋球閥，焊接球閥，氣動球閥，法蘭球閥，電動球閥；

衛生級蝶閥，焊接蝶閥，卡箍直通蝶閥，螺紋蝶閥，法蘭蝶閥，氣動蝶閥，電動蝶閥；

不銹鋼衛生泵，不銹鋼衛生級離心泵，不銹鋼衛生自吸泵，不銹鋼酒精防爆泵，衛生奶泵，衛生飲料泵；

止回閥，過濾器、呼吸器、換向閥、防混閥、安全閥；304不銹鋼衛生級內螺紋電動三通球閥廠家

衛生級不銹鋼管件，焊接彎頭，快裝彎頭，不銹鋼三通，快裝三通，四通，真空彎頭，大小頭；

罐頂組件系列，不銹鋼儲罐，發酵罐，不銹鋼衛生級人孔，清洗球/器，視鏡燈，排氣閥等其它非標產品生產加工；

我們竭誠為您服務.